Kolsch (again)

I saved the yeast from my last batch of Kolsch, and given the time of year I though I'd get another one on asap to deal with visitors. This is a beer I don't mind drinking, but not a favourite by any means. All the same, it requires a certain amount of skill to come up with a very pale, clean tasting beer, with no-where to hide in terms of fermentation issues etc.

An early tasting of the previous batch

I decided to change the recipe a little, based on a Jamil recipe from a Kolsch article of his in a 2009 issue of BYO magazine. This is just Pilsner malt and wheat malt in a 95/5 ratio. I had planned to go with Hallertau hops, but my brew shop was all out, so I went with Spalt. This is a hop which many people report as having quite an odd flavour profile. I'm interested to see what it's like in the finished beer.

Mashing was at 65 for 50 mins (recirculated through HEX), then mash out at 75 for 10. I no-chilled this beer. One unusual thing about my brewing setup is that I never measure volumes, just guess based on experience how much water/wort I've got at each point. This has never let me down before, but on this brew I ended up with 22.5L of 1.044 wort instead of 20L of 1.049 (after trub losses). This is actually quite a mess up, and is a bit of a wake up call for me, I need to sort out my volume measurements.

Anyhow, here's the recipe:

4.72KG Joe White Pilsner Malt
0.25KG Joe White Wheat Malt

30g 4.75%AA Spalt hops @50
10g 4.75%AA Spalt hops @10

whirlpooled for 20, then no-chilled.

This will stay in the no-chill cube until the London Pride clone is done fermenting, then I'll pitch some WY2565 slurry to this and ferment at 16 (one degree lower than the last batch). I'll also give it a blast of O2 and try to dry it out a little. The previous batch is not quite dry enough based on early tastings.

Brunswick Pride

I've had a bag of grain ready for brewing for several months, and a smack pack of yeast in the fridge for over a year. Yesterday I decided to put both to work to see if good quality beer can result in such old ingredients.

First off, I had a mix of 95% Simpsons Maris Otter, 5% Simpsons Dark Crystal which was supposed to go into a Fullers ESB type beer. The yeast is a WYeast 1026PC cask ale, manufactured June 2013!

Chewing on the grains I discovered that they still had plenty of crunch with no discernible musty notes. The yeast I smacked and waited about 8 hours until I could see that the pack was beginning to swell. At this point I decided to bank this yeast in glycol stocks. I made a quick post on aussiehomebrewer.com about this.

I was still not too sure about the actual viability of the yeast, so the wort was no-chilled to ensure that it can wait until I either propogate or buy some healthy yeast.

Given the yeast issues, I dumped about 800g of my grains to come up with the following grain bill:

4.67Kg Simpsons Maris Otter
0.25Kg Simpsons Dark Crystal

then very loosely based on a Can You Brew It Fuller's London Pride recipe, the hop bill is as follows:

12g Northdown @60mins
22g East Kent Goldings @60mins

18g Northdown @ 0mins
25g East Kent Goldings @ 0mins

I took 250ml, 700ml and 2L wort samples for stepped starters, and no chilled the rest. The mash was recirculated at 65.5 for 50mins, mash out at 78 for 10. I got pretty good efficiency here - OG of 1.051 for 75%, a little more than I expected.

My yeast adventures began with pitching the 100ml remaining in the 18 month old WYeast pack into 250ml of wort. I watched this for two days but there was no discernible activity. Despite this there was a slight drop in gravity so I decided to pitch this to the 700ml wort flask. After another day or so I had lots of activity in this flask, but this failed to pass the sniff inspection (never mind the taste inspection). It had serious medicinal/phenolic aromas. Either the yeast has mutated severely, or most likely I've got some Brett or something in there. I will try to streak out a few colonies from the frozen stocks to see what I come up with, but this won't be done in time to ferment this batch.

The solution is a fresh smack pack of WY1968 london esb ale yeast. This will be pitched to my 2L starter tonight, followed by pitching to the main batch tomorrow. Fermentation will be at 18C rising to 20 towards the end.

Had I known for sure that the WY1026 was a no-go, I would have mashed a little lower to achieve better attenuation. However, I have just gotten myself a little pure oxygen aeration kit, so 60secs of Oxygen may help to boost yeast health and numbers and achieve a dryer finish. Updates on this fermentation will follow.